top of page
blue-1634110_1280.png

Magnetic flux (Φ, or φ) is the total magnetic field passing through a defined surface, calculated as the surface integral of magnetic flux density (B) over that area. Flux density (B) measures how concentrated the field is at a single point. Flux accounts for both the strength of the field and the size and orientation of the surface it crosses, so it describes the cumulative field across an entire functional area.

Industrial Applications

In precision magnetic engineering, flux is a key input for predicting motor torque, actuator holding force, and inductive coupling efficiency. Force and torque are ultimately calculated from the flux density in the working gap together with geometry and current (for a voice coil, F = B × L × I), so gap flux is the link between a magnet's output and the mechanical result.


A surface Gauss reading captures flux density at a single point on a pole face. A total flux measurement evaluates the bulk output of a permanent magnet or a complete magnetic circuit, which makes it better suited to quality assurance and magnetic characterization. Fluxmeters are used with search coils or Helmholtz coils and report flux (or flux linkage, which is flux multiplied by coil turns) in Maxwells or Webers. A search coil measures the flux through its own area, while a Helmholtz coil with a fluxmeter measures a magnet's total magnetic moment.


In voice coil actuators (VCMs), magnetic torque couplings, and PVD sputtering magnetrons, designers control how much flux crosses the working air gap and how much is lost to parasitic leakage paths.

Technical Specifications

Mathematical Definition


For a uniform field perpendicular to a flat surface:

• Φ = B × A

For a uniform field at an angle θ to the surface normal:

• Φ = B × A × cos θ

For non-uniform fields across a curved or complex surface:

• Φ = ∬ B · dA

The integral is taken over an open surface, such as a pole face, a coil cross-section, or an air-gap cross-section. Net flux through any closed surface is always zero (Gauss's law for magnetism).


Terms and Units


• Φ (or φ) = total magnetic flux

◦ CGS unit: Maxwell (Mx), where 1 Mx = 1 G × cm²

◦ SI unit: Weber (Wb), where 1 Wb = 10⁸ Mx = 1 volt-second

• B = magnetic flux density (magnetic induction)

◦ CGS unit: Gauss (G)

◦ SI unit: Tesla (T), where 1 T = 10,000 G

• A (or dA) = surface area (or area element), oriented along the surface normal

◦ CGS unit: square centimeters (cm²)

◦ SI unit: square meters (m²)


Common Engineering & Manufacturing Challenges


  • Flux leakage: Some flux never crosses the working gap and instead takes parallel paths through air or nearby ferromagnetic material. Leakage grows as the gap becomes large relative to the pole dimensions, because the gap's reluctance rises and alternative paths become more attractive. Failing to model it causes engineers to overestimate the usable working flux.

  • Fringing effect: Flux in the gap bows outward at the pole edges, effectively enlarging the gap area. Estimates based only on pole-face area can misstate the flux density in the working region, and the error is largest in wide gaps.

  • Return path saturation: Mild steel or back-iron pole pieces channel flux within a circuit. If the cross-section of the steel is too thin, the material reaches its saturation flux density (Bsat) and the excess flux spills into surrounding areas, including sensitive electronics.

  • Thermal drift and demagnetization: Rising temperature lowers a magnet's remanence (Br), which reduces available flux in environments such as high-speed motors and vacuum processing chambers. This drift is largely reversible. Exceeding a magnet's maximum operating temperature or its demagnetizing field limit causes permanent flux loss.

Related Case Studies and Products

Optimize Your Magnetic Flux Circuit


Whether you are dealing with flux leakage in a compact sensor enclosure or need to maximize usable field across an open vacuum air gap, QT Magnetic Solutions provides complete concept-to-production engineering.


Ready to review your design tolerances? Contact our Silicon Valley engineering team directly at engineering@qtmagneticsolutions.com or submit your technical specifications through our Contact Page.

FLUX, MAGNETIC

QT Magnetic Solutions     561 Monterey Rd.       Morgan Hill, CA 95037       (408) 261-3589

© CONTENT COPYRIGHT 2026 QT MAGNETIC SOLUTIONS. ALL RIGHTS RESERVED.

bottom of page